Mounts : Related Mount Products : RDL, Radio Design Labs - D-BT1A

Wall-mounted Bluetooth Audio Format-A Interface

Model: D-BT1A

Bluetooth audio input for installed sound system
Intuitive single button pairing with led status indication
Special software not required for module setup
Customize the module id name and programming password through the bluetooth connection
Sends received bluetooth audio to rdl format-a receivers

More Product Information Below

Compare

Project List

Product Info

Related Products

Accessories

The D SERIES-BT1A modules are Bluetooth audio receiving modules compatible with RDL® Format-A twisted pair receivers. When paired with a compatible Bluetooth enabled devices, the module receives stereo audio from the Bluetooth source. The stereo signal is sent through two Format-A pairs to any RDL Format-A receiver. A stereo/mono switch set by the installer permits summed mono audio to be sent over one switch-selected pair to the Format-A receiver. If set for stereo operation, an additional Format-A source (set to Pair A) may be daisy chained with the D SERIES-BT1A to a three-pair Format-A receiver. If set for mono operation, up to three D SERIES-BT1A modules may be daisy chained to a single three-pair Format-A receiver. Connections between Format-A modules and Format-A receivers use standard CATx cable with RJ45 connectors.

The D SERIES-BT1A modules are powered from the Format-A receiver. The installer can customize the module name and programming password through the Bluetooth connection using a smartphone, computer or tablet terminal program.

These modules feature studio-quality circuits and analog filters to provide audio performance exceeding expectations from consumer interface technologies. High performance, simplicity of operation and efficiency of installation make RDL the best value in professional Bluetooth interfaces.

Bluetooth audio input for installed sound system
Intuitive single button pairing with led status indication
Special software not required for module setup
Customize the module id name and programming password through the bluetooth connection
Sends received bluetooth audio to rdl format-a receivers
Mono summed or stereo audio input mode is switch-selectable on rear panel
Rear-panel switch selects which RJ45 pair (A, B or C) is fed in mono summed mode
Daisy-chain up to three D SERIES-BT1A modules to one Format-A receiver in mono mode
Remotely powered through twisted pair cable
Signal and power pair pass-through on RJ45 jacks

D-TPR1A - Active Single-Pair Receiver - Twisted Pair Format-A - XLR mic/line output

D-TPR2A - Active Two-Pair Receiver - Twisted Pair Format-A - Stereo Phono jack Outputs

D-TPR3A - Active Three-Pair Receiver - Twisted Pair Format-A - XLR and stereo phono outputs

D-TPS2A - Active Two Pair Sender Twisted Pair Format-A Stereo RCA Jack Inputs

DB-TPS1A - DB-TPS1A Active Single-Pair Sender - Twisted Pair Format-A - XLR microphone input with phantom

FP-TP4PW - Power Inserter - Twisted Pair - Four Sets of Outputs - Signal Loop-through

FP-TPX3A - Format-A Twisted Pair Remote Controlled Mixer

RU-TP4PW - Power Inserter - Twisted Pair - four sets of outputs - signal loop-through

RU-TPDA - Active Distributor - Twisted Pair Format-A - RDL Format-A input to Four outputs

RU-TPS4A - Active Sender / Distributor - Twisted Pair Format-A - Three audio inputs to Four outputs

TX-TP1PW - Power Inserter

TX-TPR1A - Active Single-Pair Receiver

TX-TPR3A - Active Three-Pair Receiver - Twisted Pair Format-A - balanced line outputs

TX-TPR6A - Passive Single-Pair Receiver, Twisted Pair Format-A

TX-TPS1A - Active Single-Pair Sender, Twisted Pair Format-A

TX-TPS6A - Passive Single-Pair Sender, Twisted Pair Format-A

CP-1
Single Cover Plate - white

CP-1G
Single Cover Plate - gray

CP-1S
CP-1S Single Cover Plate, Stainless Steel

CP-2
Double Cover Plate - white

CP-2G
Double Cover Plate, Gray

CP-2S
CP-2S Double Cover Plate, Stainless Steel

CP-3
CP-3 Triple Cover Plate - white

CP-3G
Triple Cover Plate, Gray

CP-3S
CP-3S Triple Cover Plate, Stainless Steel

CP-4
CP-4 Quadruple Cover Plate - white

CP-4G
Quadruple Cover Plate, Gray

CP-4S
CP-4S Quadruple Cover Plate, Stainless Steel

DC-1G
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-1W
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-2G
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-2W
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-3G
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-3W
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-4G
Desktop or Wall Mounted Chassis for Remote Controls and Panels

DC-4W
Desktop or Wall Mounted Chassis for Remote Controls and Panels

RM-D3
19" Rack Mount for 3 Decora® Modules

SMB-1G
Surface Mount Boxes for Remote Controls and Panels

SMB-1W
Surface Mount Boxes for Remote Controls and Panels

SMB-2G
Surface Mount Boxes for Remote Controls and Panels

SMB-2W
Surface Mount Boxes for Remote Controls and Panels

SMB-3G
Surface Mount Boxes for Remote Controls and Panels

SMB-3W
Surface Mount Boxes for Decora® Remote Controls and Panels

SMB-4G
Surface Mount Boxes for Remote Controls and Panels

SMB-4W
Surface Mount Boxes for Decora® Remote Controls and Panels

WB-1U
Universal Wall Box, Single

WB-2U
Universal Wall Box, Double

Suggested Products

Projector Stacking Frame - Alfa Model (635 mm Wide)

by EPSON

Projector Stacking Frame - Beta Model (695 mm Wide)

by EPSON

Mounting Brackets (2 pack)

by Vanco International