4-channel Microflex Advance Audio Network Input Interface
Model: ANI4IN
- Single Ethernet port carries Dante audio, power (PoE - class 0)
- LEDs indicate device status and audio signal
- Control strings for third-party preset controllers including Crestron® and AMX®
- 4 Band C/S PEQ on every channel
- Provides channel summing to combine input signals and send them over a single Dante™ channel
Converts up to four line/mic analog signals onto a Dante network for easy audio routing and browser-based control.
The Audio Network Interface shall convert 4 analog audio channels into independent digital audio input channels on a Dante™ network. Microphone, auxiliary, and line-level devices are supported, with adjustable gain and +48V phantom power for each channel. In networked conferencing systems, the Audio Network Interface shall provide a simple way to connect analog equipment, such as wired or wireless microphones, onto the audio network. Available in XLR and block connector versions, each box uses a single network cable to receive audio and power through Power over Ethernet (PoE). The web application shall control built-in digital signal processing, including channel settings, parametric equalization, and audio summing from any computer connected to the same network. The block connector model shall provide logic connections (switch and mute) to convert analog logic signals to Ethernet command strings.
- Single Ethernet port carries Dante audio, power (PoE - class 0)
- LEDs indicate device status and audio signal
- Control strings for third-party preset controllers including Crestron® and AMX®
- 4 Band C/S PEQ on every channel
- Provides channel summing to combine input signals and send them over a single Dante™ channel
- Browser-based software control for all device parameters, per input channel:
- Preamp gain
- Mute control
- Digital gain
- Polarity control
- Phantom power
- 1/3 Rack unit wide
- Chassis ground screw (BLOCK version only) provides common chassis ground for multiple inputs
- Available in block connector (audio + logic) and standard XLR variations
- Applications:
- Conferencing
- Available Options:
- ANI4IN-XLR: 4-Channel Dante™ Mic/Line Audio Network Interface-In with XLR connectivity
- ANI4IN-BLOCK: 4-Channel Dante™ Mic/Line Audio Network Interface-In with Block connectivity and Logic functionality
- Warranty - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 19.94 F
- Active Power: 10 Watt
- DC Voltage: 48 Volts
- Depth: 5 in
- Height: 1.60 in
- Width: 5.50 in
- Product Weight: 1.50 lbs
- Warranty (Length/Type): 2 Year Limited
- Inputs:
•ANI4IN-XLR (4) XLR connector
•ANI4IN-BLOCK (4) 6-pin block connector - Logic Connections (Block connectors only):
•Sent as Ethernet command strings
•LED, Switch - Polarity:
•Non-inverting, any input to any output - Output:
• (1) RJ45 - Power Requirements:
•Power over Ethernet (PoE), Class 0 - Control Application:
•HTML5 Browser-based - Storage Temperature Range:
•-29°C (-20°F) to 74°C (165°F) - NETWORKING:
•Cable Requirements
•Cat 5e or higher (shielded cable recommended) - Frequency Response:
•20 to 20,000Hz - Dante Digital Output:
•Channel Count 4
•Sampling Rate 48kHz
•Bit Depth 24 - Latency:
•Does not include Dante latency
•0.35ms - Analog Gain Range:
•Adjustable in 3dB steps
•51dB - Dynamic Range (Analog-to-Dante):
•20Hz to 20kHz, A-weighted, typical
•113dB - EQUIVALENT INPUT NOISE:
•20Hz to 20kHz, A-weighted, input terminated with 150-ohm
•Analog Gain Setting = +0dB, -93dBV
•Analog Gain Setting = +27dB, -119dBV
•Analog Gain Setting = +51dB, -130dBV - Total Harmonic Distortion:
•@ 1kHz, 0dBV Input, 0dB analog gain
•<0.05% - Common Mode Rejection Ratio:
•150-ohm balanced source @ 1kHz
•>70dB - Impedance:
•5 k-ohm - Input Configuration:
•Active Balanced - Input Clipping Level:
•Analog Gain Setting = +0dB, +20dBV
•Analog Gain Setting = +27dB, -7dBV
•Analog Gain Setting = +51dB, -31dBV - Built-in Digital Signal Processing:
•Per Channel: Equalizer (4-band Parametric), Mute, Invert Polarity, Gain (140 dB range)
•System: Audio Summing
Suggested Products
WEBB Integration
1420 S 4800 W
Suite D2
Salt Lake City, UT 84104
USA
(801) 484-8567
www.webbintegration.com